Command line ftps windows

These commands run automatically after ftp starts. This parameter allows no spaces. Specifies the computer name, IP address, or IPv6 address of the ftp server to which to connect. The host name or address, if specified, must be the last parameter on the line. This command toggles back and forth between the operating system and ftp. Once back in the operating system, typing exit takes you back to the FTP command line.

Lists files, if connected. Sets globbing on or off. When turned off, the file name in the put and get commands is taken literally, and wildcards will not be looked at. I need to write a batch file to auto upload a backup every day.

I'm restricted to Windows. Is there free software to do this? I was looking at FileZilla , but the command line interface doesn't let you auto upload files, and I need to buy a license for CuteFTP. However, from what I can gather, you need a FTP client for both. Filezilla is a good one that users I've dealt with never complained was too hard to figure out. To use SFTP, you need a key exchange. Overkill is to get to sftp, but Cygwin is a nice toolset. Depending on your needs, you could scale the install back to only the minimum you need or scale it up and use Bash, Python, etc.

It may serve your needs. Sign up to join this community. The best answers are voted up and rise to the top. Sign up or log in Sign up using Google.

Sign up using Facebook. Sign up using Email and Password. Post as a guest Name. Email Required, but never shown. The Overflow Blog. Stack Gives Back Safety in numbers: crowdsourcing data on nefarious IP addresses. Featured on Meta. New post summary designs on greatest hits now, everywhere else eventually. Related 1. Hot Network Questions. Question feed. Server Fault works best with JavaScript enabled.

If the file is protected by a password, use the -pfxpw parameter. See also -pfxpwfile. Do not use both -pfxpw and -pfxpwfile. For example, you might specify -ports MOVEit Freely will restrict the port numbers it uses to be greater than or equal to low , and less than or equal to high.

For active mode, this restricts the port numbers sent by the PORT command. For passive mode, this controls the port number of the originating end of the connection. This very rarely used option exists to accommodate highly restrictive firewall rules. This will exit a script file without reading any more commands.

The default is to read commands from the console. This applies to both the amount of time to wait for the server to connect back on a non-passive data port , and the amount of time to wait without data before declaring a data socket dead.

The default is seconds. If this is not specified, the program will prompt for a username upon initial connect. By default, if there is a problem with a certificate, MOVEit Freely will display a dialog, asking whether you want to accept the certificate.

The most common problem is that a certificate was issued by a non-trusted certification authority, as happens with test certificates. The default is 21, unless -e:implicit has been specified, in which case the default is In this case, you must issue an open command to connect to an FTP server.

Here are some examples of this syntax in use: FTPS ftp. MOVEit Freely command-line syntax was itself based on the command-line syntax of the Microsoft non-secure ftp. This uniformity allows people to convert many scripts based on "ftp. MOVEit Freely will return an exit value of zero 0 if no errors occurred during the processing of a file transfer session.

See the example below for a batch file that checks the return code for errors. If the -quiterror parameter is specified, MOVEit Freely will exit immediately with an exit code of 3 as soon as an error occurs without reading any more commands from the script file or console. Resuming Transfers The -resume parameter can be used to cause MOVEit Freely to attempt to resume a transfer that may have been interrupted in a previous execution.

Resuming transfers requires support on the corresponding FTP server, but not all server implementations have that support. Here is how the -resume parameter works: When a get operation is performed, MOVEit Freely will first check to see if there is already a local file present. If so, a "REST xxxxx" command is sent to the server with "xxxxx" being the size in bytes of local copy of the file. Then, when the file is transferred, the first "xxxxx" number of bytes are skipped by the server and MOVEit Freely will write the data sent to the end of the local file.

The server is responsible for writing the data to the end of the file. It is important to note that use of the -resume parameter will cancel the ability of MOVEit Freely to overwrite a file if it already exists. A destination file, if it exists, is assumed to be a partially transferred version of the source file. If you often transfer different versions of a file with the same name with overwrite, do not use -resume.

When MOVEit Freely "file integrity mode" is used with MOVEit Transfer, a partial transfer that is completed by using the -resume parameter is verified, by checksum, that the entire destination file matches the source file. That is, a file which was completely received by MOVEit Transfer cannot be extended using the -resume feature.

The commands are read from the console, or from the script filename if the -s parameter has been specified on the command line. If the -quiterror parameter has been used and an error is encountered, either a 4xx or 5xx response from the server or a syntax or file error detected by MOVEit Freely itself , MOVEit Freely will exit without reading any more commands from the console or script file.

If a command that has required parameters is entered without the parameters, MOVEit Freely will prompt for the parameters, using the same prompts as Windows 's FTP. For many commands, to enter a parameter containing spaces, you must enclose the parameter in double quotes.

For instance, to retrieve a file named My Document. The only exceptions to this rule are the dir, lcd, ls, and quote commands, which do not require double quotes. Executes a shell command on the local machine. If cmd is not specified, a copy of the command interpreter is launched. You can type as many Windows commands as you like. If cmd is specified, that command is executed, then control is returned to MOVEit Freely, with no need to type exit.

Displays a brief description of MOVEit Freely, the current version, and a link to the vendor's website.